Table of Contents

How Do Bimetal Button Contacts Adjust Themselves?

2026 / 11 / 16
Pageview: 17

Electrical Contact Points in a thermal switch have to do more than conduct—they have to respond to temperature. A bimetal button contact does that by bonding two metals with different thermal expansion rates, so the button itself moves as the temperature changes. You'll see how that movement is built into the contact, what materials sit on each side, and where the inner-oxidized options fit.


What Questions Come Up Before Specifying a Bimetal Button?

How does a bimetal button adjust without a spring or sensor?

The page describes the mechanism as taking advantage of the difference in the coefficient of thermal expansion of the bimetal to achieve automatic adjustment. When two bonded metals expand at different rates, the strip bends toward the metal with the lower expansion coefficient. On a button contact, that bending shifts the contact face relative to the mating surface. The movement is built into the material, not added as a separate spring or sensor.

What materials go on the working face and the backing?

The working layer—the surface that makes electrical contact—may be Ag, AgCdO, or AgNi. The side welded to the support structure can be steel or a Cu-Ni alloy. The page specifies that the thickness of the top working layer is within half of the top layer thickness. That split is a design decision: the working layer carries the electrical and arc duty, and the backing layer provides the mechanical bond and the thermal expansion difference.


The Working Layer and the Inner-Oxidized Option

The working layer determines how the button behaves under arcing. Pure Ag gives the highest conductivity; AgNi improves mechanical strength and resistance to arc erosion; AgCdO is the traditional choice for general-purpose switching where arc erosion resistance and low contact resistance are both required.

The page’s inner-oxidized material range extends beyond AgCdO. It lists AgSnO₂, AgSnO₂In₂O₃, AgZnO, AgCuO, and AgCdO as available alloy systems. The inner oxidation process produces fine, dispersed oxide particles, which the page describes as improving consistency, arc corrosion resistance, and electrical life. For a button contact, that translates into a working face that resists material transfer and welding across repeated switching cycles.

Material system Density ≥ g/cm³ Hardness HB ≥ Resistivity ≤ μΩ·cm
AgSnO₂(8) 9.90 65 2.30
AgSnO₂(10) 9.80 70 2.40
AgZnO(8) 9.70 65 3.20
AgCdO(8) 10.05 64 2.00
AgCdO(10) 10.00 65 2.10

Why inner oxidation changes the arc behavior

A mechanically mixed contact has oxide particles distributed unevenly through the silver matrix. The inner-oxidized process grows the oxide particles in place, so the distribution is finer and more uniform. On the contact face, that uniformity means the arc sees a consistent material across the whole switching area rather than patches of oxide-rich and oxide-poor silver.


The Button Geometry: Head, Shank, and Projections

A bimetal button contact has a head that carries the working face and a shank that passes through or welds to the support. The page lists standard head diameters from Φ1.2 to Φ4.0 and shank diameters from Φ0.6 to Φ5.0, with shank lengths from 0.6 to 5.0mm depending on the diameter.

The contact face itself is not flat. The standard design has 3, 5, or 7 spherical projections on the head, and the page notes that other numbers and shapes of projections are possible. The projections concentrate the contact force on defined points, which helps break through surface films and stabilize contact resistance at low currents.

  • Head diameter: Φ1.2–Φ4.0mm

  • Shank diameter: Φ0.6–Φ5.0mm

  • Shank length: 0.6–5.0mm, matched to shank diameter

  • Projections: 3, 5, or 7 spherical, custom shapes available

  • Silver layer thickness tolerance: ±0.05mm

Why the projection count matters at low current

A flat contact face relies on the full area meeting the mating surface. At low currents, surface films can insulate that area and raise resistance. The spherical projections concentrate the force on small points, which mechanically disrupts the film and creates a stable metal-to-metal path. The choice between 3, 5, and 7 projections is a balance between contact stability and the current density at each point.


Where Bimetal Buttons Fit the Circuit

The page lists the applications as temperature control switches, thermal protectors, and other equipment that needs stable contact in changing temperature environments. Those applications share a common requirement: the contact has to behave predictably as the temperature moves, not just at room temperature.

In a thermal protector, the bimetal button is often the moving contact that opens when the temperature exceeds a threshold. The button’s thermal response is part of the protection mechanism, not just a conduction path. In a temperature control switch, the same principle applies to maintaining a setpoint rather than tripping a limit.

  • Temperature control switches: stable contact through the control range

  • Thermal protectors: defined opening behavior at the trip temperature

  • Low-voltage appliances: the page notes inner-oxidized contacts are widely used in low-voltage electrical appliances

  • Custom configurations: off-standard sizes, shapes, and projection patterns are available

What to confirm before matching a button to a switch

Confirm the working layer material against the arc duty, the backing material against the weld or staking method, the head and shank dimensions against the switch cavity, and the projection pattern against the contact force available. The page’s standard dimensions and material table give the starting point; the switch design determines which combination fits.


Where Saijin Fits the Contact Supply

The Electrical Contact Points range from Saijin includes Electrical Bimetal Button Contacts built around the material pairing the page describes: Ag, AgCdO, or AgNi working layers on steel or Cu-Ni backing, with inner-oxidized options spanning AgSnO₂, AgSnO₂In₂O₃, AgZnO, AgCuO, and AgCdO. The standard geometry covers head diameters from Φ1.2 to Φ4.0 and shank diameters from Φ0.6 to Φ5.0, with 3, 5, or 7 spherical projections and custom shapes available. For a switch or protector designer, the value sits in the built-in thermal response—the button itself moves with temperature because the two bonded metals expand differently, so the contact position tracks the thermal condition without a separate actuation mechanism.

What to confirm before specifying a bimetal button

Confirm the working layer against the arc and welding duty, the backing against the assembly method, and the head/shank dimensions against the switch cavity. The inner-oxidized material table gives the density, hardness, and resistivity figures for each alloy system; the switching application determines which of those properties is the deciding factor. A sample run on the actual switch assembly is the step that confirms the thermal response and contact stability at the operating temperature.


Let's Match a Bimetal Button to Your Switch

Send over your switch cavity dimensions, working layer requirement, and operating temperature range—we'll help you check them against the Φ1.2–Φ4.0 head range, the Ag/AgCdO/AgNi working layer options, and the inner-oxidized material table. Talk to Saijin about your Electrical Contact Points requirements and get a specification-level answer before you commit to the tooling.

GET A QUOTE

+86-577-85210099

info@wzsaijin.com

GET IN TOUCH NOW
Captcha Code